yogisaw
Posts: 22
Location:
Rank: Novice
 |
| 28 Jan 2010 8:27 PM |
 Alert
|
Hi all
I have some strange problem.
I have been using wilcom ES 2006. few days before when I turned my pc on it but could not start wilcom
I remember that hasplm service needed was closed by windows, I tried to manually start the service but same error message cropped. and would not start wilcom
I tried with a fresh install of xp but still the problem remained
what could be the problem I also found that there was no files in alladinshared folder
pls somebody help me to find out what is the reason for this problem and how to overcome this
thankx
|
|
|
|
|
delfius
Posts: 188
Location: Sydney, Australia
Rank: Hooked
|
| 28 Jan 2010 9:46 PM |
Alert
|
Try this:
- go to "C:\Program Files\Wilcom\ES2006\bin"
- run the ES.exe from there
What error message do you get?
|
|
Ballads, duets, and a fun dose of pop/rock  http://www.youtube.com/user/delfiusgarland |
|
|
yogisaw
Posts: 22
Location:
Rank: Novice
|
| 29 Jan 2010 12:58 AM |
Alert
|
| The err actually belogs to windows xp when i start windows it flashes hasplm has encountered an err and need to close
wilcom doesn't open it shows es window and close |
|
|
|
|
delfius
Posts: 188
Location: Sydney, Australia
Rank: Hooked
|
| 29 Jan 2010 8:29 PM |
Alert
|
Try this:
- Click Start->Run...
- Enter "C:\Program Files\Wilcom\ES2006\bin\ES.EXE" (assuming you installed it there) and click OK
- Wait for a couple of minutes! (it will look like nothing is happening, no splash screen or progress or anything so just wait a bit)
After a couple of minutes, either ES will start, or else ES will give an error message and an error number, which may be useful in trying to figure out what's going on.
|
|
Ballads, duets, and a fun dose of pop/rock http://www.youtube.com/user/delfiusgarland |
|
|
yogisaw
Posts: 22
Location:
Rank: Novice
|
| 29 Jan 2010 10:15 PM |
Alert
|
wilcom is not giving any err msg instead it simply quits after first flash screen
it cannot be started either by shourtcut or by manually typing the command including the command line parameters |
|
|
|
|
delfius
Posts: 188
Location: Sydney, Australia
Rank: Hooked
|
| 01 Feb 2010 8:44 PM |
Alert
|
The shortcut actually runs DESLOADR.EXE with a bunch of command line parameters.
Just to clarify, I'm suggesting to run ES.EXE (with NO command line parameters), not the DESLOADR.EXE that the shortcut runs.
Running ES.EXE will NOT display the splash screen, but should give you a message I'm pretty sure (I remember the old versions of ES, sometimes the splash screen used to clobber the message).
|
|
Ballads, duets, and a fun dose of pop/rock http://www.youtube.com/user/delfiusgarland |
|
|
telmd
Posts: 11
Location:
Rank: Novice
|
| 10 Feb 2010 1:25 AM |
Alert
|
| I started getting the DESLOADR.EXE Error about a week ago. Switched the shortcut switch up this morning so we shall see what that does. |
|
|
|
|
embessentials
Posts: 2
Location:
Rank: Newbie
|
| 22 May 2010 2:32 AM |
Alert
|
*** POST REMOVED ***
THE CONTENT OF THIS POST IS ILLEGAL AND HAS BEEN REMOVED.
THIS USER WILL BE REPORTED TO AUTHORITIES.
EmbroideryStartup.com does not tolerate illegal activities.
|
|
|
|
|
halim.label
Posts: 1
Location:
Rank: Newbie
|
| 18 Jun 2010 5:12 PM |
Alert
|
i can not start wilcom v9.0
smartheap library mem_bad_pointer
solution |
|
|
|
|
delfius
Posts: 188
Location: Sydney, Australia
Rank: Hooked
|
| 23 Jun 2010 9:29 PM |
Alert
|
halim.label, what operating system are you running?
|
|
Ballads, duets, and a fun dose of pop/rock http://www.youtube.com/user/delfiusgarland |
|
|